Short Lead Time for Ultrasonic Cleaner For Nuts And Bolts Cleaning Machine - ICU electric hospital bed DHC-III(FM05) – VinnieVincent

1. Specification:
Overall dimension: L2170 × W1080 × H500/850mm，
Bed panel: L1950 × W910mm；
2. The overall lifting is 500 ~ 850mm, the back plate is adjusted by 65 ° ± 5 °, the legs are adjusted by 45 ° ± 5 °, the two sections of the lower leg plate are adjustable, and the fore-and-aft inclination is 13 ° ± 3 °;
3. Equipped with scientific weighing function, weighing accuracy is 50-100g, can be reset, and equipped with weighing display. No matter the patient is in any position, just touch a button, the built-in weighing system can measure, and the data can be accurately displayed at the display on the bed tail board;
4. Bed frame: 60 * 30 * 3.0mm high-quality cold drawn rectangular tube is used as the girder, and 60 * 30 * 3.0mm high-quality cold drawn rectangular tube is welded with rungs at both ends. It can fully ensure the bearing capacity of the bed ≥ 240kg;
5. Bed surface: high quality anti Beite bed board, with X-ray transmission throughout the body; It has the characteristics of good anti-corrosion, acid and alkali resistance and various chemical reagents; The back plate is equipped with a film cassette to realize X-ray photography of the patient’s upper body in the bed;
6. The bed body is made of Dutch Akzo Nobel environmental protection antibacterial powder by electrostatic spraying, which can prevent Staphylococcus cross infection, and has the characteristics of anti-corrosion, rust prevention and exquisite appearance;
7. The headboard and tailboard of the bed are made of high-quality drug-resistant PE resin material, which is blow molded as a whole, with skin texture treatment on the surface, easy to clean and arc-shaped design. The outside of the head and tail of the bed is equipped with anti-collision angle wheels, which can be replaced separately, which can effectively prevent the hospital bed from colliding with the wall during movement. The four anti-collision angles are equipped with oxygen cylinder bracket hanging holes (see Annex). The bed tail board has a transparent acrylic patient information card slot;
8. The guardrail is a new American guardrail made of high-quality PE material, which is blow molded as a whole. Each guardrail is equipped with a damper device to control speed and noise. It is firm, durable, fast and light. The guardrail design meets the requirements of IEC safety regulations, beautiful, generous and safe;
9. The front and rear guardrails are equipped with ball angle display, which can clearly display the rising angle of the bed board of the back and legs and the inclination angle of the bed body. A 30 degree scale mark is required to be set on the guardrail to clarify the angle at which the back rises by 30 degrees, which can effectively assist clinical VAP pneumonia;
10. Imported double-sided casters with a diameter of 125mm are adopted, with locking, free and directional three-stage central control locking device; High stability linkage system, silent, corrosion-resistant, large braking force, stable and safe;
11. It is equipped with mattress skid arrester. There are five places on both sides of the back plate and at the foot of the bed, which can avoid the side sliding of the mattress and improve the safety. It is equipped with a fixed position of restraint belt, 3 on the left and 3 on the right;
12. The manual CPR operation wrench device on the left and right sides of the bed can realize rapid treatment and reduce medical accidents in case of emergency. One drainage hook on the left and right sides, with a load of ≥ 3kg;
13. The motor adopts timoshen medical motor, which has stable speed control, low noise, long service life, safety and reliability. The guide rod system adopts high carbon steel and high-strength aluminum platform, and two-way pole overload protection screw rod;
14. Accessories: there are drip bar, power assisted hanging rod, oxygen bottle rack and other optional accessories.